| Author |
Message |
|
MSouthwell25
|
Post subject: Cruel C51 drilling  Posted: Wed Dec 08, 2010 6:30 am |
|
Joined: Wed Dec 08, 2010 5:55 am
Posts: 3
|
|
Hi,
I have recently ordered the motiv cruel and was wondering if someone could help me with a suggested layout. Unfortunately I don't know as much about layouts and drilling as I would like.
I am a two handed lefty and bowl about 17mph. We currently have a house pattern of 39feet. However I'm looking at this ball as more of an investment for when I play on more sport patterns and tournaments.
Any help would be appreciated.
Thanks
Matt
|
|
| Top |
|
 |
|
DjResol
|
Post subject: Re: Cruel C51 drilling Posted: Wed Dec 08, 2010 10:15 am |
|
Joined: Tue Mar 02, 2010 11:06 am
Posts: 326
Location: Houston
|
|
Your stats will be needed. pap, tilt, the more you give the better the advise.
_________________
Pound for Pound
Gt1 - 1-300 1-289 1-287 1-280 5-279
Rx1(Orange)
Sr2 - 1-290 1-279
Tv4 added!50x45@4.75" - 1-289 2-279
3 - 300's
high series 791 - 796 - 785 - 824
|
|
| Top |
|
|
|
hudwood
|
Post subject: Re: Cruel C51 drilling Posted: Thu Dec 09, 2010 9:43 am |
|
Joined: Tue Aug 31, 2010 6:26 pm
Posts: 77
|
|
most all twohanded bowls layouts work better with fullrollers...i have been one for 17 years ...there are some others that work also...jason belmo..all his balls are fullrollers ...
jim hud
motiv staff
|
|
| Top |
|
|
|
JustinWi
|
Post subject: Re: Cruel C51 drilling Posted: Thu Dec 09, 2010 11:53 am |
|
Joined: Thu Aug 27, 2009 10:43 pm
Posts: 1688
Location: Rochester NY
|
|
If possible more specific stats on your delivery would be helpful. Primarily rev rate and tilt, as well as what conditions you are looking for it to attack. Is it intended to be an arsenal piece for when you encounter oil?
|
|
| Top |
|
|
|
MSouthwell25
|
Post subject: Re: Cruel C51 drilling Posted: Thu Dec 09, 2010 5:34 pm |
|
Joined: Wed Dec 08, 2010 5:55 am
Posts: 3
|
|
Yeh my PAP is 6" over .75" up
Don't know my tilt unfortunately. Does that matter too much?
|
|
| Top |
|
|
|
MSouthwell25
|
Post subject: Re: Cruel C51 drilling Posted: Thu Dec 09, 2010 5:39 pm |
|
Joined: Wed Dec 08, 2010 5:55 am
Posts: 3
|
|
Rev rate is 500-550.
I am thinking of this more for the longer patterns, 44-45 foot. Most of my balls are currently mid range. This will be my primary high performance ball.
|
|
| Top |
|
|
|
JustinWi
|
Post subject: Re: Cruel C51 drilling Posted: Thu Dec 23, 2010 8:20 pm |
|
Joined: Thu Aug 27, 2009 10:43 pm
Posts: 1688
Location: Rochester NY
|
|
With a rev rate that high, use a drilling angle of 70*. If you want it smoother 55* VAL angle, sharper 35* VAL angle. Use a 5.5"-5.75" pin.
|
|
| Top |
|
|
