| Author |
Message |
|
Bluff
|
Post subject: Needs Some help with More Motiv balls  Posted: Thu Dec 16, 2010 2:43 pm |
|
Joined: Thu Dec 16, 2010 2:28 pm
Posts: 6
|
|
I got a Tx1 and So far I love how it rolls and Carries.
My spec are
16Mph
400 Rev
PAP - 4 1/2 down 1/4
AT= 13
Rotation 0 to 60
I drilled the TX1 -
80 x 3 x 30 - P3.5 Weight Hole Box Finish
Now I ordered a SR2 whats should be a good layout for it?
I bowl Mostly Amateur Tournaments. Want to used this maybe as a benchmark ball any suggestions would greatly appreciated.
I am thinking 70 / 3 1/4 / 25 or 80 x 4 x 30
|
|
| Top |
|
 |
|
captmike02
|
Post subject: Re: Needs Some help with More Motiv balls Posted: Mon Dec 20, 2010 5:45 pm |
|
Joined: Mon Sep 28, 2009 10:29 pm
Posts: 304
Location: Massillon, OH
|
Be careful putting the SR2 in the leverage area. I had a SX1 leverage and it never had any back end, it looked good in the mid lane but spent all the energy up front. You and I have similar ball speed and rev rates. I haven't purchased a SR2 yet but I was thinking of 60x5.5x35, 3 to 3.5 pin. That will give me room to place a hole. The core is a strong core, and the 5 to 5.5 pin to pap will still get the ball rolling but let the core retain more energy before it hits the break point. Guys like you and I seems to like the SR2. Don't be afraid of using surface as well. Don't be in a rush to put a x hole in the ball until you've tried a few combinations of surfaces. I think my next purchase will be the SR2 and the Feb release. Need to drill a few more balls to get the capitol.
Good luck,
Mike
P.S. check out my youtube for all my vids.http://www.youtube.com/user/qtey2002?feature=mhum
_________________
Motiv Staff
RX1s 60x6x70
QZ2 1 inch pin to pap
Thrash 1 inch pin to pap
QZ2 BACKDRAFT 60x5x65
TZ3 70x5.5x30
Primal Impulse 90x3.5x55
Primal Impulse 75x5.5x40
Sigma Tour 80x5.5x40
Raptor Attack 95x5.25x30
Raptor P7 45x4.5x30 P1
More not listed!!!
|
|
| Top |
|
|
|
Bluff
|
Post subject: Re: Needs Some help with More Motiv balls Posted: Mon Dec 20, 2010 6:58 pm |
|
Joined: Thu Dec 16, 2010 2:28 pm
Posts: 6
|
|
Will have to see how the SR2 goes. Looks like I will get the RX1 peral for sure when I got some extra $$$
|
|
| Top |
|
|
|
JustinWi
|
Post subject: Re: Needs Some help with More Motiv balls Posted: Tue Dec 21, 2010 1:35 am |
|
Joined: Thu Aug 27, 2009 10:43 pm
Posts: 1688
Location: Rochester NY
|
|
Being rev dominant, a 45x45@4.75".
Box surface, no hole to start. If you want a stronger midlane read, use a P3 on the Projected PSA method. For a bit more backend, a P3 paralell. To tame a touch P1.
|
|
| Top |
|
|
