| Author |
Message |
|
t.nick
|
Post subject: good layouts for a high track roller  Posted: Tue Jan 04, 2011 3:37 am |
|
Joined: Tue Jan 04, 2011 1:54 am
Posts: 6
|
|
i have cruel with pin down in the middle of the fingers stacked with cg and it rolled over both finger so bad
|
|
| Top |
|
 |
|
Sikfish
|
Post subject: Re: good layouts for a high track roller Posted: Tue Jan 04, 2011 9:59 am |
|
Joined: Wed Aug 11, 2010 10:04 am
Posts: 102
Location: Coldwater, Michigan
|
Do you have a picture of the ball that you could post here? If the layout allows, you maybe able to add a extra hole, low, to get your bowtie to move up and off the fingers...... Brian MOTIV staff www.motivbowling.com
|
|
| Top |
|
|
|
JustinWi
|
Post subject: Re: good layouts for a high track roller Posted: Tue Jan 04, 2011 10:56 am |
|
Joined: Thu Aug 27, 2009 10:43 pm
Posts: 1690
Location: Rochester NY
|
With a high track it is imperative to keep the pin even, or preferably above the fingers. With the pin below like you have, as the axis migrates the track rolls over the fingers. If you provide your specs, I can give you a layout to use after a plug and redrill.Sikfish wrote: If the layout allows, you maybe able to add a extra hole, low, to get your bowtie to move up and off the fingers...... The only issue here is that the more dynamic the ball, the less of an impact placing a hole will have on the bowtie. With the Cruel having the strongest dynamic capability currently on the market, the chances of a hole modulating the bowtie properly are slim. Not impossible, but highly unlikely.
|
|
| Top |
|
|
|
Sikfish
|
Post subject: Re: good layouts for a high track roller Posted: Tue Jan 04, 2011 11:37 am |
|
Joined: Wed Aug 11, 2010 10:04 am
Posts: 102
Location: Coldwater, Michigan
|
|
@justin - that is why I was looking for a picture, if it was a slight "clip" of the fingers - the hole may work (did on mine)...if he was all over the holes, then, most def. and plug and redrill.....no harm, no foul....
|
|
| Top |
|
|
|
t.nick
|
Post subject: Re: good layouts for a high track roller Posted: Tue Jan 04, 2011 1:42 pm |
|
Joined: Tue Jan 04, 2011 1:54 am
Posts: 6
|
|
i already had it redrilled and @justin it was on both fingers right over them and i put a hole in it and it didnt stop it so i had it drilled and it dont roll over them now but it rolls right were the holes used to be ill post how he redrilled it with pics later of the cruel and the rx1s after work thanks guy
|
|
| Top |
|
|
|
t.nick
|
Post subject: Re: good layouts for a high track roller Posted: Tue Jan 04, 2011 6:18 pm |
|
Joined: Tue Jan 04, 2011 1:54 am
Posts: 6
|
|
70X5X60 track circ 12 axis horz 5 7/8 vert none its 1000 and polished were should put a hole at to get as early as posible
|
|
| Top |
|
|
|
JustinWi
|
Post subject: Re: good layouts for a high track roller Posted: Tue Jan 04, 2011 7:28 pm |
|
Joined: Thu Aug 27, 2009 10:43 pm
Posts: 1690
Location: Rochester NY
|
|
What is your speed and rev rate?
|
|
| Top |
|
|
|
t.nick
|
Post subject: Re: good layouts for a high track roller Posted: Wed Jan 05, 2011 10:06 am |
|
Joined: Tue Jan 04, 2011 1:54 am
Posts: 6
|
|
| Top |
|
|
|
StickZ
|
Post subject: Re: good layouts for a high track roller Posted: Wed Jan 05, 2011 10:47 pm |
|
Joined: Mon Oct 11, 2010 3:58 pm
Posts: 394
Location: Countdown County FLA
|
|
50x50@5'....personal recommendation justin gave to me and its amazing!
_________________
Jason Drouin
"StickZ"
Self-Proclaimed
House Hack Motiv Staff =)
|
|
| Top |
|
|
|
Pinbasher209
|
Post subject: Re: good layouts for a high track roller Posted: Wed Jan 05, 2011 11:53 pm |
|
Joined: Tue May 04, 2010 3:47 pm
Posts: 18
|
Any way Motiv can get creative and educate Drillers? Especially about low pin on High Flare balls? I had the same problem with My TR2, My Driller wanted me to plug and re-drill after my new bowling ball tracked over my fingers, Hey T.Nick welcome to Motiv and I hope you enjoy your new ball that's been plugged and re-drilled. For Some Staff members it's OK, to have mistakes on drillings because they have more access to Motiv bowling balls, but for a hard working stiff like myself, I'm just stuck junk of a ball, and 179.00 down the drain, one very expensive door stop.  Any Motiv Staffers willing to make me a satisfied customer?? A replacement would be nice.. I'll even pay the shipping of this ball back to you.. Let me know I'll be looking for your replies...
|
|
| Top |
|
|
