Author |
Message |
JustinWi
|
Post subject: Re: drill layout Posted: Tue Apr 26, 2011 12:58 am |
|
Joined: Thu Aug 27, 2009 10:43 pm Posts: 1707 Location: Rochester NY
|
|
Top |
|
 |
JustinWi
|
Post subject: Re: drill layout Posted: Tue Apr 26, 2011 1:02 am |
|
Joined: Thu Aug 27, 2009 10:43 pm Posts: 1707 Location: Rochester NY
|
oviewan wrote: I came up with 5 1/8"x 1 1/8 up. Was this PAP coordinate verified?
|
|
Top |
|
 |
GervAce
|
Post subject: Re: drill layout Posted: Tue Apr 26, 2011 1:47 am |
|
Joined: Tue Apr 12, 2011 5:59 pm Posts: 60 Location: Sioux Falls, SD
|
My LE is drilled very similar to this. My right finger hole may be just a hair closer to the dot and my counter hole (think that's what it is but new to the terminology) is a lot smaller but in a very similar location. I noticed in throwing a few balls after it was drilled that I had to step forward some and aim further right or I hit Brooklyn quite a bit. When I did hit the pocket though, and even the brooklyns, the ball just smashed the pins. I worry a bit that it may be too much ball if I cannot get used to it but I did only throw a few balls with it. I am eager to get more of your thoughts on the layout Justin. Im actually going to be contacting the guy who drilled it to give me the exact numbers and I will post them.
***Edit*** I went down and rechecked my ball, the fingers are probably an inch closer to the pin and slightly lower than on the ball shown and my thumbhole is a bit further left of that bottom mark as I prefer to have my thumbhole slightly left of center. In any case my counter hole is much smaller.
_________________ In the Bag
Cruel C51 LE- 247/663
QZ2 Backdraft
Primal Impulse-300/735- 2nd career 300 03/08/12
Monster Bruiser-1st ever 300 03/24/11-668
Black Ice-(Black) (sb)
|
|
Top |
|
 |
oviewan
|
Post subject: Re: drill layout Posted: Tue Apr 26, 2011 6:23 am |
|
Joined: Sun May 23, 2010 4:11 pm Posts: 124
|
pap coordinate verified? No...5 1/8" x 1 1/8" up might be right. I did my pap and came up with 5 1/8" x 7/8"up.
|
|
Top |
|
 |
JustinWi
|
Post subject: Re: drill layout Posted: Tue Apr 26, 2011 10:23 am |
|
Joined: Thu Aug 27, 2009 10:43 pm Posts: 1707 Location: Rochester NY
|
Gotta find your PAP or your layout could be anywhere. That is more of a P3 hole as well, which explains why it is a bit smoother.
|
|
Top |
|
 |
oviewan
|
Post subject: Re: drill layout Posted: Tue Apr 26, 2011 4:52 pm |
|
Joined: Sun May 23, 2010 4:11 pm Posts: 124
|
I measured for my pap today, using a tape measure 5 1/8" x 1 1/8" up seems right
|
|
Top |
|
 |
JustinWi
|
Post subject: Re: drill layout Posted: Tue Apr 26, 2011 5:09 pm |
|
Joined: Thu Aug 27, 2009 10:43 pm Posts: 1707 Location: Rochester NY
|
The pic you sent didn't look right, so I laid out a ball here.

I don't know what exactly you have on your LE, but it isn't 55x25@3.5" P2 hole based on a PAP of 5.125" over and 1.125" up.
|
|
Top |
|
 |
oviewan
|
Post subject: Re: drill layout Posted: Tue Apr 26, 2011 8:13 pm |
|
Joined: Sun May 23, 2010 4:11 pm Posts: 124
|
Well, I gave the "PRO", the guy who sold me the ball, the drill layout I wanted. That's the 2nd motiv ball from him and he's never talk PAP. I don't know what it is either, I gave him 55x25x3.5 P2 hole and asked him to drill that layout?? and what's with the big P2 hole. I don't think the guy knows what he's doing. But he's the only guy that sells motiv in N.H. Did you notice the thumb insert, it dropped below the coverstock.
|
|
Top |
|
 |
FUPAsnack
|
Post subject: Re: drill layout Posted: Wed Apr 27, 2011 2:01 am |
|
Joined: Mon Feb 14, 2011 12:50 pm Posts: 1204 Location: San Antonio, TX
|
It's always sad to see when others have bad drilling experiences.
|
|
Top |
|
 |
oviewan
|
Post subject: Re: drill layout Posted: Wed Apr 27, 2011 8:00 am |
|
Joined: Sun May 23, 2010 4:11 pm Posts: 124
|
Well there are no 14lb. LEs left. I'm thinking plugged and redrilled. Will the ball loose any gusto?
|
|
Top |
|
 |