| Author |
Message |
|
254Efrain
|
Post subject: JustinWi - Raptor Layout  Posted: Sun Aug 07, 2011 2:40 pm |
|
Joined: Fri Oct 30, 2009 8:23 pm
Posts: 120
|
|
I just pick up a Raptor, 14lbs, 3in Pin. What would you recommend? Here is my information:
Bowl right handed
Speed at the monitor: 15.48avg
Axis Tilt: 13*
Axis Rotation: 30* -60*
PAP: 3 3/4 – 7/16up
Can wait to drill!
Efrain Santiago
|
|
| Top |
|
 |
|
plamormick
|
Post subject: Re: JustinWi - Raptor Layout Posted: Sun Aug 07, 2011 4:08 pm |
|
Joined: Wed Sep 22, 2010 12:14 am
Posts: 776
Location: Iowa Falls, IA
|
What conditions do you wish to utilize the Raptor on? What shape were you seeking? (I know I'm not Justin, but I have a guess what he'd say here, and I'm waiting to see if I've learned enough on the forum to be close.) 
_________________
Lane 13 Pro Shop, Iowa Falls, IA ............. * Recon
Proprietor, Pla-Mor Bowl ......................... Thrash Frenzy.
Vise Grips Amateur Staff ..........................
|
|
| Top |
|
|
|
254Efrain
|
Post subject: Re: JustinWi - Raptor Layout Posted: Sun Aug 07, 2011 4:23 pm |
|
Joined: Fri Oct 30, 2009 8:23 pm
Posts: 120
|
plamormick wrote: What conditions do you wish to utilize the Raptor on? What shape were you seeking? (I know I'm not Justin, but I have a guess what he'd say here, and I'm waiting to see if I've learned enough on the forum to be close.) PBA patterns and looking for something with a sharper breakpoint. I'm thinking about 40 x 4 1/4 x 25.
|
|
| Top |
|
|
|
plamormick
|
Post subject: Re: JustinWi - Raptor Layout Posted: Sun Aug 07, 2011 4:46 pm |
|
Joined: Wed Sep 22, 2010 12:14 am
Posts: 776
Location: Iowa Falls, IA
|
|
Wow, that was kinda close to what I had in mind.
50 x 4 x 35
Let's see what the master says...
_________________
Lane 13 Pro Shop, Iowa Falls, IA ............. * Recon
Proprietor, Pla-Mor Bowl ......................... Thrash Frenzy.
Vise Grips Amateur Staff ..........................
|
|
| Top |
|
|
|
254Efrain
|
Post subject: Re: JustinWi - Raptor Layout Posted: Sun Aug 07, 2011 6:13 pm |
|
Joined: Fri Oct 30, 2009 8:23 pm
Posts: 120
|
plamormick wrote: Wow, that was kinda close to what I had in mind.
50 x 4 x 35
Let's see what the master says... Your layout is pretty good. I use 1.6:1 ratio on my layout.
|
|
| Top |
|
|
|
JustinWi
|
Post subject: Re: JustinWi - Raptor Layout Posted: Sun Aug 07, 2011 7:02 pm |
|
Joined: Thu Aug 27, 2009 10:43 pm
Posts: 1690
Location: Rochester NY
|
|
| Top |
|
|
|
254Efrain
|
Post subject: Re: JustinWi - Raptor Layout Posted: Sun Aug 07, 2011 8:13 pm |
|
Joined: Fri Oct 30, 2009 8:23 pm
Posts: 120
|
JustinWi wrote: What's your rev rate? 325
|
|
| Top |
|
|
|
JustinWi
|
Post subject: Re: JustinWi - Raptor Layout Posted: Mon Aug 08, 2011 2:19 pm |
|
Joined: Thu Aug 27, 2009 10:43 pm
Posts: 1690
Location: Rochester NY
|
254Efrain wrote: Speed at the monitor: 15.48avg
Rev Rate:325
Axis Tilt: 13*
Axis Rotation: 30* -60*
PAP: 3 3/4 – 7/16up 55x35@3.5" Most likely a small P3 or P2 hole, throw it before placing the hole. For longer heavier patterns, a touch with 2k might make it read a bit truer off the spot.
|
|
| Top |
|
|
