MOTIV

Username: Log me on automatically each visit
Password:
It is currently Thu Jul 24, 2014 9:00 am


Post a new topicPost a reply Page 4 of 6   [ 53 posts ]
Go to page Previous  1, 2, 3, 4, 5, 6  Next
Author Message
 Post subject: Re: drill layout
PostPosted: Tue Apr 26, 2011 12:58 am 

Joined: Thu Aug 27, 2009 10:43 pm
Posts: 1698
Location: Rochester NY
Image


Top
 Profile  
 
 Post subject: Re: drill layout
PostPosted: Tue Apr 26, 2011 1:02 am 

Joined: Thu Aug 27, 2009 10:43 pm
Posts: 1698
Location: Rochester NY
oviewan wrote:
I came up with 5 1/8"x 1 1/8 up.


Was this PAP coordinate verified?


Top
 Profile  
 
 Post subject: Re: drill layout
PostPosted: Tue Apr 26, 2011 1:47 am 

Joined: Tue Apr 12, 2011 5:59 pm
Posts: 60
Location: Sioux Falls, SD
My LE is drilled very similar to this. My right finger hole may be just a hair closer to the dot and my counter hole (think that's what it is but new to the terminology) is a lot smaller but in a very similar location. I noticed in throwing a few balls after it was drilled that I had to step forward some and aim further right or I hit Brooklyn quite a bit. When I did hit the pocket though, and even the brooklyns, the ball just smashed the pins. I worry a bit that it may be too much ball if I cannot get used to it but I did only throw a few balls with it. I am eager to get more of your thoughts on the layout Justin. Im actually going to be contacting the guy who drilled it to give me the exact numbers and I will post them.

***Edit***
I went down and rechecked my ball, the fingers are probably an inch closer to the pin and slightly lower than on the ball shown and my thumbhole is a bit further left of that bottom mark as I prefer to have my thumbhole slightly left of center. In any case my counter hole is much smaller.

_________________
In the Bag

Cruel C51 LE- 247/663

QZ2 Backdraft

Primal Impulse-300/735- 2nd career 300 03/08/12

Monster Bruiser-1st ever 300 03/24/11-668

Black Ice-(Black) (sb)


Top
 Profile  
 
 Post subject: Re: drill layout
PostPosted: Tue Apr 26, 2011 6:23 am 

Joined: Sun May 23, 2010 4:11 pm
Posts: 120
pap coordinate verified? No...5 1/8" x 1 1/8" up might be right. I did my pap and came up with 5 1/8" x 7/8"up.


Top
 Profile  
 
 Post subject: Re: drill layout
PostPosted: Tue Apr 26, 2011 10:23 am 

Joined: Thu Aug 27, 2009 10:43 pm
Posts: 1698
Location: Rochester NY
Gotta find your PAP or your layout could be anywhere. That is more of a P3 hole as well, which explains why it is a bit smoother.


Top
 Profile  
 
 Post subject: Re: drill layout
PostPosted: Tue Apr 26, 2011 4:52 pm 

Joined: Sun May 23, 2010 4:11 pm
Posts: 120
I measured for my pap today, using a tape measure 5 1/8" x 1 1/8" up seems right


Top
 Profile  
 
 Post subject: Re: drill layout
PostPosted: Tue Apr 26, 2011 5:09 pm 

Joined: Thu Aug 27, 2009 10:43 pm
Posts: 1698
Location: Rochester NY
The pic you sent didn't look right, so I laid out a ball here.

Image

I don't know what exactly you have on your LE, but it isn't 55x25@3.5" P2 hole based on a PAP of 5.125" over and 1.125" up.


Top
 Profile  
 
 Post subject: Re: drill layout
PostPosted: Tue Apr 26, 2011 8:13 pm 

Joined: Sun May 23, 2010 4:11 pm
Posts: 120
Well, I gave the "PRO", the guy who sold me the ball, the drill layout I wanted. That's the 2nd motiv ball from him and he's never talk PAP. I don't know what it is either, I gave him 55x25x3.5 P2 hole and asked him to drill that layout?? and what's with the big P2 hole. I don't think the guy knows what he's doing. But he's the only guy that sells motiv in N.H. Did you notice the thumb insert, it dropped below the coverstock.


Top
 Profile  
 
 Post subject: Re: drill layout
PostPosted: Wed Apr 27, 2011 2:01 am 

Joined: Mon Feb 14, 2011 12:50 pm
Posts: 1204
Location: San Antonio, TX
It's always sad to see when others have bad drilling experiences.


Top
 Profile  
 
 Post subject: Re: drill layout
PostPosted: Wed Apr 27, 2011 8:00 am 

Joined: Sun May 23, 2010 4:11 pm
Posts: 120
Well there are no 14lb. LEs left. I'm thinking plugged and redrilled. Will the ball loose any gusto?


Top
 Profile  
 
Display posts from previous:  Sort by  
Post a new topicPost a reply Page 4 of 6   [ 53 posts ]
Go to page Previous  1, 2, 3, 4, 5, 6  Next


Who is online

Users browsing this forum: No registered users and 2 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  


Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group

MOTIV