MOTIV

Username: Log me on automatically each visit
Password:
It is currently Sun Nov 23, 2014 9:22 pm


Post a new topicPost a reply Page 1 of 1   [ 10 posts ]
Author Message
 Post subject: Which ball can fill between SR2 and QZ1 ?
PostPosted: Wed Dec 09, 2009 11:07 pm 

Joined: Tue Dec 01, 2009 8:56 pm
Posts: 12
Location: Montreal, Canada
i already say before wanted to replace my Rapid Fire pEarl for THS conditions. I know QZ1 is best choice but today my pro shop has received first time every Motiv balls except QZ1.

I dont know if TX1 can fill between SR2 and QZ1
i think SX1 is for dry-short lanes.
i plan to preorder the QZ1, but i'll wait another 2-3 weeks :(
Now, i'll start with SR2

thank in advance

_________________
i'm MOTIVated!
Montreal, Canada


Top
 Profile  
 
 Post subject: Re: Which ball can fill between SR2 and QZ1 ?
PostPosted: Thu Dec 10, 2009 3:27 am 

Joined: Thu Aug 27, 2009 10:43 pm
Posts: 1701
Location: Rochester NY
The GT1 would seem to fit. Please elaborate on the layouts on your current balls to determine the proper layout to make your GT1 rock socks.


Top
 Profile  
 
 Post subject: Re: Which ball can fill between SR2 and QZ1 ?
PostPosted: Thu Dec 10, 2009 9:56 am 

Joined: Tue Dec 01, 2009 8:56 pm
Posts: 12
Location: Montreal, Canada
based on MOtiv drill sheet, mostly i drill every ball with LENGTH + LEVERAGE with PIN above fingers, some balls are LEVERAGE drill for more hook. Im low-med track , med-rev , low-speed

i play alot in tournament 1-2x per month and leagues.

ARe you sure GT1 is under than SR2 ? cause it's kinda same category balls for med-heav oil. OOB GT1 is little more agressive

i'll drill SR2 and i'll comeback to you. In weekend, i'll post video for better idea and doing comparison with Rapid Fire, Nomad Pearl, Virtual Gravity.

_________________
i'm MOTIVated!
Montreal, Canada


Top
 Profile  
 
 Post subject: Re: Which ball can fill between SR2 and QZ1 ?
PostPosted: Thu Dec 10, 2009 11:24 am 

Joined: Thu Jul 02, 2009 4:01 pm
Posts: 539
I would also recommend the GT1 provided you place the pin at or below the right finger and polish w/Power Gel Polish, of course. I got mind to go pretty long w/this drilling and surface adjustment. Nicely so that I did quite well with it on a short 35'-37' PBA pattern playing the 4 board. The SX1 is another good choice but will give you alittle more "pop" off the pattern then the GT1. W/O seeing you throw the ball it is difficult to make a accurate recommendation. But since you are choicing a Motiv ball, you can't go wrong. Good Luck!

_________________
Bob "Mick" Michalojko
Colonial Lanes Pro Shop
PBA Member
Motiv Staff Member
Turbo Xtreme Dealear Member


Top
 Profile  
 
 Post subject: Re: Which ball can fill between SR2 and QZ1 ?
PostPosted: Thu Dec 10, 2009 12:45 pm 

Joined: Tue Dec 01, 2009 8:56 pm
Posts: 12
Location: Montreal, Canada
i dont need to polish the GT1. This ball is already polished OOB !
check the specs : "FINISH 1000 Wet Sand / Power Gel Polish"

_________________
i'm MOTIVated!
Montreal, Canada


Top
 Profile  
 
 Post subject: Re: Which ball can fill between SR2 and QZ1 ?
PostPosted: Thu Dec 10, 2009 1:28 pm 

Joined: Sat Oct 10, 2009 9:39 pm
Posts: 282
If you're looking for somthing to fit under the SR2, depending on layout and surface prep, then take a look at the TX1. The GT1 will be more aggressive than what you're looking for I think.

For me the next step down is purple QZ1, then TX1, then SX1, then red QZ1. Again, it will depend on the surface and layout a little bit, but the TX1 is probably what you wanna take a look at.

_________________
Get MOTIVated!
Josh Stephens
Motiv Regional Staff


Top
 Profile  
 
 Post subject: Re: Which ball can fill between SR2 and QZ1 ?
PostPosted: Fri Dec 11, 2009 12:11 am 

Joined: Thu Aug 27, 2009 10:43 pm
Posts: 1701
Location: Rochester NY
The best part of the GT1 that is often overlooked is the lower differential, or flare potential, of the ball. But, it has the strongest overstock in the line. These characteristics make it an incredibly versatile ball. Drill it weak to be weak, drill it strong to be strong.


Top
 Profile  
 
 Post subject: Re: Which ball can fill between SR2 and QZ1 ?
PostPosted: Fri Dec 11, 2009 3:05 am 

Joined: Thu Nov 19, 2009 4:33 am
Posts: 11
the sr2 and the tr 2 have the strongest coverstocks not the gt 1 which is pearl but the differential is lowest in the gt1. :mrgreen:


Top
 Profile  
 
 Post subject: Re: Which ball can fill between SR2 and QZ1 ?
PostPosted: Fri Dec 11, 2009 11:20 am 

Joined: Thu Aug 27, 2009 10:43 pm
Posts: 1701
Location: Rochester NY
Kenny Parks wrote:
the sr2 and the tr 2 have the strongest coverstocks not the gt 1 which is pearl but the differential is lowest in the gt1. :mrgreen:



Incorrect. MOTIVator-T is the strongest cover in the line, regardless of pearlizing. Highest oil absorption rate and Ra.


The covers in order from strongest to weakest:

MOTIVator-T (GT1)

MOTIVator-R (TR2, SR2)

MOTIVator-Z (QZ1)

MOTIVator-X (SX1, TX1)


Top
 Profile  
 
 Post subject: Re: Which ball can fill between SR2 and QZ1 ?
PostPosted: Fri Dec 11, 2009 11:57 am 

Joined: Tue Dec 01, 2009 8:56 pm
Posts: 12
Location: Montreal, Canada
thank for useful informations !
imagine the next release around february 2010 will be with Motivator-T with solid covertsock. why not ;)


Top
 Profile  
 
Display posts from previous:  Sort by  
Post a new topicPost a reply Page 1 of 1   [ 10 posts ]


Who is online

Users browsing this forum: Bing [Bot], Yahoo [Bot] and 4 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  


Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group

MOTIV