| Author |
Message |
|
TooMuchHand
|
Post subject: Help me layout a QZ1 purple  Posted: Mon Dec 21, 2009 1:26 pm |
|
Joined: Wed Nov 18, 2009 10:01 am
Posts: 70
|
|
This will probably be my next ball.
Here are my specs:
PAP - 4 7/8" left; 3/4" up
Rev - 380-400
Speed - 19-19.5 mph
What specs should I look for in the ball? I want something to make it through the feathers and make a strong move on the back end. I do not want to have swing out to the dry to make it hook. I leave too many 7's this way. Something that charges hard off the 2nd range finder would suit me best.
Thanks in advance!
_________________
Best Game - 300 (9)
Best Series - 840 (3 800's)
In the bag:
Raging Bull 45x4x60 P2 hole
Solaris Blackout 60x4.5x35 P2 hole
SR2 55x4.75x45 no hole yet
Victory Road Solid 50x4.5x40 with a P2
715T 55x3x35 with a P3 hole
T-zone
|
|
| Top |
|
 |
|
Brian.Woodman
|
Post subject: Re: Help me layout a QZ1 purple Posted: Mon Dec 21, 2009 2:28 pm |
|
Joined: Mon Jun 22, 2009 4:28 pm
Posts: 26
|
|
The one thing I have noticed is the QZ1's is they roll better with a little surface. I would recommend putting the surface at 2000 Scuff Polish, then clean it and hit it with a 500 abralon pad. After that I would do a longer pin from your PAP to reduce track flare and try to keep it above the fingers. That would still leave you enough backend to hopefully chop that 7 pin out but still utilize the ball with the surface, but that is for a house shot type of condition.
|
|
| Top |
|
|
|
TooMuchHand
|
Post subject: Re: Help me layout a QZ1 purple Posted: Mon Dec 21, 2009 2:32 pm |
|
Joined: Wed Nov 18, 2009 10:01 am
Posts: 70
|
|
That sounds like a good approach. Most of my equipment has the pin 1/2" to 2" above my ring.
_________________
Best Game - 300 (9)
Best Series - 840 (3 800's)
In the bag:
Raging Bull 45x4x60 P2 hole
Solaris Blackout 60x4.5x35 P2 hole
SR2 55x4.75x45 no hole yet
Victory Road Solid 50x4.5x40 with a P2
715T 55x3x35 with a P3 hole
T-zone
|
|
| Top |
|
|
|
JustinWi
|
Post subject: Re: Help me layout a QZ1 purple Posted: Mon Dec 21, 2009 3:59 pm |
|
Joined: Thu Aug 27, 2009 10:43 pm
Posts: 1690
Location: Rochester NY
|
|
45x40@4" P2 or P3 hole.
1000 Abralon to start.
|
|
| Top |
|
|
|
evil858
|
Post subject: Re: Help me layout a QZ1 purple Posted: Tue Dec 29, 2009 1:25 am |
|
Joined: Mon Jun 22, 2009 11:08 am
Posts: 14
|
|
if you really want to tighten the flare on the ball put a flare decreasing hole on the left side of your v a l ive seen flare on other balls go from four inches down to two inches by doing this
|
|
| Top |
|
|
